FAQ / Life on Pern / Craft Information / Vintner Craft / Beer
Please note: The FAQ is no longer updated; for current info please see the Wiki
Last updated 22nd July 2005 by Bree
Beer Brewing
Barley is the grain most often used in brewing beer, and will be what is meant whenever 'grain' is mentioned. The following describes the process of malting and drying the grain and brewing it into beer.
During the malting process, the barley is soaked in a vat for 40 candlemarks. The water is changed several times to prevent bacteria from infecting the grain. The water is drained off, and the grain is left in the vat for 6 to 12 additional candlemarks. The barley is then laid out in a well-ventilated room and allowed to germinate. This process requires considerable amounts of oxygen and creates a lot of heat. The resulting barley is called green malt.
Next is the drying. The germinated grain is put into a kiln and heated. This heating process can take 35 to 40 candlemarks. The temperature is kept very low in the beginning and then raised, to cure the malt.
After the grain is roasted, it is screened to remove the sprouts. These sprouts can be fed to herdbeasts so as not to waste them. The remaining kernels are milled or ground into grist.
The grist is poured into a mash tun, where it is soaked and stirred in hot water (140+ degrees). This is when the sugars and flavors are extracted. The temperature in the mash determines the character of the beer:
high temp = sweet and rich
low temp = less sweet and light
This "bath" lasts for a couple of candlemarks. The mash is then drained through screens to remove impurities. The resultant wort is placed into a large copper kettle.
At this point comes the addition of hops to the brewing malt. The flavors desired from the hops boil away in high temperatures, so it is added in the last few minutes of the brewing process. Hops can also be added immediately before the beer is bottled or kegged.
After a few candlemarks of brewing, the liquid is placed in a cooling tank and rapidly cooled. The next step is transfer to a fermentation tank. Yeast may be added at this time. After fermenting for two to five sevendays, during which the mixture must be stirred occasionally, the beer can be kegged or bottled.
See Also: No articles yet
Referenced By: No articles yet
During the malting process, the barley is soaked in a vat for 40 candlemarks. The water is changed several times to prevent bacteria from infecting the grain. The water is drained off, and the grain is left in the vat for 6 to 12 additional candlemarks. The barley is then laid out in a well-ventilated room and allowed to germinate. This process requires considerable amounts of oxygen and creates a lot of heat. The resulting barley is called green malt.
Next is the drying. The germinated grain is put into a kiln and heated. This heating process can take 35 to 40 candlemarks. The temperature is kept very low in the beginning and then raised, to cure the malt.
After the grain is roasted, it is screened to remove the sprouts. These sprouts can be fed to herdbeasts so as not to waste them. The remaining kernels are milled or ground into grist.
The grist is poured into a mash tun, where it is soaked and stirred in hot water (140+ degrees). This is when the sugars and flavors are extracted. The temperature in the mash determines the character of the beer:
high temp = sweet and rich
low temp = less sweet and light
This "bath" lasts for a couple of candlemarks. The mash is then drained through screens to remove impurities. The resultant wort is placed into a large copper kettle.
At this point comes the addition of hops to the brewing malt. The flavors desired from the hops boil away in high temperatures, so it is added in the last few minutes of the brewing process. Hops can also be added immediately before the beer is bottled or kegged.
After a few candlemarks of brewing, the liquid is placed in a cooling tank and rapidly cooled. The next step is transfer to a fermentation tank. Yeast may be added at this time. After fermenting for two to five sevendays, during which the mixture must be stirred occasionally, the beer can be kegged or bottled.
See Also: No articles yet
Referenced By: No articles yet